How to glue the film on the wall of the aquarium at home

Using decorative film to transform your aquarium can be a rewarding and enjoyable project. Applying film to the aquarium wall is an easy DIY project that you can complete at home with a few simple tools and a little perseverance, whether your goal is to create a gorgeous backdrop or just update the look of your fish tank.

It’s crucial to gather all required materials before you begin. The decorative film, a credit card or squeegee, a sharp utility knife, and a spray bottle full of soapy water are required. It will go more smoothly and be more fun if you make sure you have everything you need before starting.

Getting the surface ready is an essential first step. Thoroughly clean the exterior of the aquarium wall to get rid of any grease, dust, or dirt. Maintaining a spotless surface guarantees that the film sticks well and endures longer. Before moving on to the next step, make sure the surface is completely dry.

The film must be applied by carefully placing it on the aquarium wall and guiding it into position with the aid of the soapy water. The film slides around and aligns perfectly because the water stops it from sticking right away. After you’re happy with the arrangement, start in the center and move outwards to remove any air bubbles with the squeegee.

Ultimately, use the utility knife to trim any extra film to create a polished, tidy appearance. To prevent scratching the aquarium or damaging the film, take your time doing this step. You can have a gorgeously decorated aquarium that accentuates the beauty of your aquatic environment with a little care and attention.

How to prepare glass

The aquarium’s rear window needs to be completely cleared of pollutants. Even the smallest sorrinka will not be able to be removed later, but it can degrade the film’s glass clutch quality.

Glass liquid is used to wipe down the wall. The best cloth to use to wipe the glass surface is a microvolon, such as a microfiber, and one that leaves no trace.

If the aquarium is already in use, the following steps are taken in order to prepare it:

• fish are transplanted into a separate container;
• Water merges from the aquarium, all decorative elements and soil are obtained;
• The glass container is washed in the usual way;
• The outer side of the wall is wiped with a means for washing windows or any detergent, neatly remove dust, dirt, fat spots);
• the surface is well wiped with a paper towel, then you can immediately start gluing.

If you prepare and apply film on the wall of your home aquarium correctly, it can be a very simple process. This tutorial will take you through each step of cleaning the glass, cutting the film to size, and adhering it with a basic soapy water solution to guarantee a smooth and bubble-free application. You can achieve a professional-looking finish that improves the appearance of your aquarium and creates an amazing backdrop for your aquatic life by following these simple instructions.

How to stick a background into an aquarium

The kit contains all the necessary tools for attaching the embossed background, and you can use homemade adhesive to attach the film to the wall.

Soapy solution

The glued surface should be somewhat bigger than the sticker in order for the background to adhere firmly.

The solution is sprayed on the glass after it has been cleaned. It is made with water, dish soap, and detergent. The film is then meticulously adhered to ensure that no wrinkles or bubbles appear. The excess solution is immediately scraped off the wall surface during the gluing process.

Glycerin

Instruments and parts:

• scotch;
• glycerin or mineral oil – 25 ml;

• decorative film;
• A rag or washcloth;
• West for windows.

The movie is cropped to fit the wall’s width. It ought to be one centimeter less on each side. Using a sponge dipped in window cleaner, the glass is cleared of impurities. Using a specialized spatula that can be bought at a pharmacy, glycerin is applied to the wall and spread along its surface. The film is placed on top of the glass to create a smooth, bubble-free surface. Using a spatula, rag, or even piece of cardboard, the emerging air tubercles are extracted from beneath the film.

The corners of the film can be taped to ensure reliability and prevent them from unscrewing. Using a sponge, glycerin that had been applied along the backdrop’s edges is eliminated.

Glue

Use JBL Fixol glue if you wish to.

The adhesive composition is applied to the wall after it has been thoroughly dried and the dirt has been removed using a glass cleaning solution. To prevent peeling off and deformation during operation, the glue is applied evenly throughout the glass, paying extra attention to the corners.

The backdrop is carefully smoothed onto the wall.

You can remove the film and try gluing again if you were unable to place it evenly.

Subsequently, the air bubbles beneath the sticker are forced out with a spatula, gradually advancing from the center to the edges. After using a clean sponge to remove the glue from the sides, tape is used to adhere the film to the surrounding area.

Tape

Is the sole adhesive technique where the backdrop needs to be bigger than the wall. Applying the background to the glass, it is positioned in the upper corners of the wall. Tape is used to secure the background’s upper portion to the glass. The entire surface is carefully ironed, and tape is used to adhere the background’s lower portion and side edges.

Occasionally, water droplets may unintentionally land beneath the sticker. The image will fit in these areas more tightly, which visually detracts from the entire aquarium type.

Installing a film on an aquarium’s wall at home can be a simple and satisfying task. You can improve the aesthetic appeal of your aquarium and achieve a professional-looking finish by following the instructions provided in this guide. For optimal results, take your time properly prepping the surface, selecting the film, and applying it with care.

To begin, give the aquarium wall a thorough cleaning to get rid of any dust, dirt, or algae. In order to make sure the film sticks well and lasts longer, this step is essential. After the film has been cleaned, measure and cut it to the appropriate size, leaving some extra material on the edges to facilitate adjustments.

Use a spray bottle to lightly mist the surface with water before applying the film. This keeps air bubbles from forming and lets you move the film around as needed. Using a squeegee or other similar tool, carefully smooth out the film, working from the center outward to remove any excess water or trapped air.

Once the film is in position, trim any extra material and remove any moisture that may have remained. Prior to adding water to the aquarium, let the film completely dry. By doing this, you can be sure that the film will remain firmly in place and look good over time.

You can successfully apply a film to the wall of your aquarium, giving your aquatic environment a stunning and long-lasting backdrop with a little perseverance and attention to detail. Savor the improved aesthetic appeal and the fulfillment that comes from a job well done.

Video on the topic

Glue the aquarium background on soap.

How to stick a background from a self -adhesive Oracal film on the aquarium

How to stick a background on an aquarium

How to quickly glue the rear background in the aquarium

How to stick backs + gifts of gifts correctly

How to glue the rear background on the aquarium! Using glycerol or petroleum.