Wall plastering technology through a grid

Plastering walls is a basic part of construction and remodeling that guarantees surfaces are level, long-lasting, and prepared for finishing. Using a plastering grid is one practical way to increase the stability and durability of plastered walls. By using this technique, the plaster is strengthened and common problems like uneven surfaces and cracking are avoided by encasing a mesh material within the wall.

The plastering grid serves as a support structure inside the plaster layer and is usually constructed of fiberglass or metal. It improves plaster adhesion to the wall and its ability to withstand environmental stresses by adding strength. This technique works especially well in places where there are frequent temperature changes or uneven wall surfaces.

Plastering through a grid is a simple process, but it needs to be done carefully and with attention to detail. The wall surface has to be spotless and clear of any loose debris first. The grid is then firmly fastened to the wall to make sure it covers every area that will be plastered. After that, the grid is covered in plaster to incorporate it into the mixture. A smooth, crack-resistant finish that is both aesthetically pleasing and structurally sound is ensured by this methodical process.

Plastering with a plastering grid improves plaster durability and streamlines the application process. It lowers the possibility of flaws by offering a stable framework that supports the plaster while it dries. Plastering a grid can make a big difference in the longevity and quality of your walls, whether you are building a new structure or remodeling an old one.

Why do you need to reinforce the plaster, what function performs

Applying the mixture in the typical manner will result in a lengthy drying period for the initial layer. Plaster is applied faster and to the full thickness of the coating on the grid right away. The cells separate the common layer into multiple components and maintain the composition in an immobile state. If a grid is put in place, the plaster’s strength is much higher and it is not frightened by sporadic shock loads. The grid creates a single, solid slab.

Reinforcement fixes the thickness of the reinforcing layer and facilitates wall alignment. The retreat from the construction solution’s recommended humidity will be undetectable when using the grid. There’s very little chance of breaking.

If a grid is put in place, the plaster’s strength is much higher and it is not frightened by sporadic shock loads.

Utilizing a reinforcing mesh, wall plastering through a grid produces a plaster finish on walls that is more stable and long-lasting. This technique is perfect for surfaces that are prone to movement or structural shifts because it improves adhesion and helps prevent cracking. Compared to conventional plastering techniques, you can guarantee a smoother, more resilient finish that can tolerate wear and environmental conditions by embedding the grid within the plaster layers. With grid-reinforced plastering, you can achieve professional results by following this guide, which will walk you through the necessary steps and materials.

What are the types of reinforcing mesh

It is pointless to reinforce a heavy reinforcing material with a light reinforcing, a heavy sequence solution, since different mesh canvases are designed for different loads.

The canvases are composed of metal, plastic, and fiberglass. Plastic ones are intended to reinforce masonry and should only be used when applying a thin layer. Among metal nets are:

• Woven ones, they use thin wire for them, the cells of such a canvas are minimal; The wires are pushed without ri – or additionally give them stiffness;
• The wicker is obtained in the process of hanging and clutch of wire rods, another and more familiar name for such metal products-a mesh-wrapper;
• The welded canvases are inactive, they are more often produced by cards of a certain format, for plastering are used less often than wicker and woven;
• Prose-exhausted is obtained by fragmentary cutting of the metal rolling with the subsequent stretch of the sheet.

Which grid to choose, what criteria

The functionality, operational characteristics of materials, and net manufacturing features are considered when selecting a reinforcing frame. Every type of reinforcing canvas has advantages of its own.

The roller mesh materials made of their fiberglass, high strength: they bend, fold without damage. The weight of the rolls is insignificant, they are not afraid of high humidity. Clutch of a solution reinforced with fiberglass, high even when laying a thick layer. Important! Fiberglass perfectly masks the joints of panels, blocks, plates, closes all cracks, it helps to create a thin even coating with a construction mixture of any composition.

Although plastic is lightweight, it is not impervious to the chemicals found in plastering mixtures.

How to fix a grid on a wall

Mounting tape is used to secure the small-thickness reinforcing frame. If the wall is concrete, dowels or screws will be needed for wicker nets. The material is cut into the appropriate size segments prior to installation. The weight of the mesh canvas and the cell size determine how far apart the mounts are spaced. 40 cm is the maximum distance.

The ideal gap should exist between the grid and the wall; the canvas should only fit firmly against the wall where fasteners are located.

Installation of fiberglass

Each piece has its mesh fixed around the edges, and the canvases are laid out last, without overlapping. Pieces’ fasteners shouldn’t line up. Because of the construction mixture’s viscosity, the grid is not fixed in the middle of the piece but will continue to hold.

Pieces are cut out of the fiberglass in order to close the wall as much as possible. This determines the plaster’s strength.

Coating with polymer canvases

The material is horizontally fastened to the wall, beginning at the ceiling and moving upward. After being stretched out on the ground, the canvases are cut. Although there is a 15 cm overlap, earning more money is not desired.

Metal coatings

Use a grinder or scissors to cut metal. First, a solvent is used to degrease the canvas and remove the lubricant used to make wire. She can make distinct oil stains on the walls.

How to plaster the walls on a reinforcing metal grid with your own hands

Prior to painting, wallpapering, or attaching other finishes to concrete, brick, or block masonry, a black facade plaster on the grid must be applied; the technology is straightforward. The most important thing is to consistently fix the reinforcing frame and prepare surfaces correctly.

Preparation of the wall for plaster and installation of lighthouses

The plaster solution is only applied to a clean base after the previous finish (paint or wallpaper) has been removed. For work, iron brushes are employed. It’s also taken into consideration if the old plaster has crumbled.

Following the installation of the beacons on both sides of the wall, the mesh is fastened. A unique profile is put on top of a gypsum solution to aid in creating a level surface. Examine the lighthouse installation by pulling the lace along the walls’ diagonals and around the perimeter.

Only after the construction mixture has dried out are plaster beacons removed from the wall.

Surgery plastering

Work is carried out in stages, plastering on the grid provides for the multi -layer of coatings. First, spray is done with a solution of sour cream consistency. With energetic movements of the hand with a trowel or bucket, the mixture is driven into the net. The thickness of spraying up to 1 cm, the solution is leveled with a trowel, dried from 4 to 8 hours, depending on the composition of the mixture. The next portion of the plaster is made thick, the layer is aligned with the rule, it is pressed to the lighthouses. The final tearing is made by liquid composition, it is rubbed with half -terriers along the misconducting area.

It is possible to create reinforced plaster on your own if you understand the nuances of the technology and how it is applied to the grid. You must consider the material’s resistance, the paintings’ specific weight, and the solution’s compatibility when selecting a grid.

Plastering a wall using a grid is a dependable and efficient technique that provides improved durability and a smooth surface. Using a mesh, be it metal or fiberglass, gives the plaster more support, reducing the chance of cracks and guaranteeing a more durable surface. This method works especially well in places where there is a chance of structural movement or where additional reinforcement is needed for the plaster layer.

Plaster application through a grid is a simple procedure that is achievable with practice. The first step is to fasten the mesh to the wall, making sure it is securely fastened and properly stretched. After that, layers of plaster are applied, the first of which embeds the mesh and the later layers of which add thickness and finish. This technique helps to create a more even surface while also reinforcing the plaster.

Plastering with a grid can greatly enhance the quality of the finished product. It lessens the possibility of typical plastering problems like uneven surfaces and cracking. This makes it the go-to option for both expert plasterers and do-it-yourselfers hoping for results on par with those of a pro. It also provides a strong base for the new plaster and is a practical solution for repairing damaged walls.

All things considered, wall plastering through a grid is a wise investment for anyone looking for a long-lasting and attractive finish. It is a great technique for a variety of plastering projects, from new construction to renovations, due to its simplicity and effectiveness. You can guarantee a durable, well-made plaster job that will last for years by using this technique.

Video on the topic

The fastest and most reliable way to fasten the plaster mesh

You can not use the grid in plaster, the errors of plastering Ceresit CT24 light, the way of correction

Plaster grid TsPVS / mesh for plaster "Volga mesh"