Wallpaper gluing technology on the OSB plates

Although adhering wallpaper to OSB (Oriented Strand Board) plates can be difficult, the correct methods and supplies will allow you to achieve a smooth and appealing finish. Because of its strength and affordability, OSB is frequently used in construction; however, because of its rough texture and porous surface, special preparation is needed before applying wallpaper.

The OSB surface needs to be properly prepared in order to guarantee that the wallpaper adheres correctly. This entails filling in any gaps or imperfections, priming the board appropriately, and sanding it to produce a smooth surface. In order to stop the wallpaper from bubbling or peeling over time, follow these instructions.

It’s crucial to select the proper adhesive and wallpaper. Not every wallpaper works well on OSB surfaces, and using the incorrect adhesive can result in poor adhesion and unsatisfactory results. The best options are frequently robust adhesives and heavy-duty wallpapers made for difficult surfaces.

You may get a long-lasting and attractive wallpaper finish by adhering to these recommendations and taking your time when preparing your OSB plates. Compared to other surfaces, this process might take a little longer, but the payoff will be a stunning and long-lasting improvement to your area.

Is it possible to glue wallpaper on OSB

When building private homes with frame technology, OSB plates are frequently utilized as exterior sheathing for interior partitions. As a result, building owners frequently wonder if OSB can be glued with wallpaper.

Holding plates (OSP), also known as panels, are composed of premium wooden chips that are glued together into multiple layers using resins, along with the addition of wax and boric acid.

This is a robust material that takes well to processing of any kind because it doesn’t react to moisture.

What will happen if the OSB is not prepared

  1. The type of finish will suffer. With proper installation, technological seams on the plates remain. They compensate for the expansion of the material. In addition to seams, the problem may be the unevenness and heterogeneity of the surface of the panels. If you do not eliminate problems, then after gluing under the canvases all the hollows, tubercles, joints and hats of self -tapping screws will be noticeable.
  2. Traces of synthetic resins. The chips from which the sheets are made is glued with different resins, including toxic formaldehyde, also in their composition there are wax. If you glue the wallpaper directly on the OSB with an increase in t ° C, then the resins will begin to stand out and appear through the finish, leaving fat traces.
  3. The canvases will be exfoliated or even fall off. The panels are impregnated with solutions that repel moisture. They protect wood chips from dampness and getting wet, but the adhesive characteristics of the material are reduced, and it will not be possible to apply wallpaper or primer on it without preliminary processing. Such funds are rolled up, and the result will not be achieved.
  4. The panel will swell due to the adhesive. If you still managed to apply glue, without a protective layer between it and the plate, the mixture is absorbed into the pores, which is brought to the swelling of the panel. It does not look aesthetic, and also negatively affects the quality of the material.

In order to prevent this kind of outcome, the OSB needs to be treated with soil after the panels have been polished.

Types of primer for OSB panels

There are three classes of soils that can process plates, each with a different composition.

  1. Acrylic. The most popular primers. They are easily applied, within an hour after priming they become safe. Drinking quickly, diluted with water. Manufacturers add additives to acrylic soils to improve their qualities: for deep penetration, to prevent the development of mold, to paint the surface. The base impregnated with soils with the content of the dye is ready for pasting. Minus acrylic agents – cannot be used at low temperatures.
  2. Alkyd.Use before they plan to paint the base with alkyd paint or apply a varnish. Alquid soil applied on the surface of the OSB significantly strengthens the plate. It does not respond to atmospheric phenomena, shows resistance to chemicals, has disinfecting properties. Has a harmful effect on the body. Therefore, it is used only in external work or in a well -ventilated room. For priming in residential premises is not suitable.
  3. Adhesive. The basis of soils is quartz chips. The panel treated with this tool can easily hold putty. The size of the crumb grain can be chosen depending on the task set in front of the solution. After priming the plates, you can proceed to putty with the subsequent pasting of the wallpaper canvases.

Shpping without putty

Those who have never finished before can glue wallpaper to the OSB without the need for putty.

Base preparation using this paste technique in multiple steps.

  1. Lining the joints between the slabs. Acrylic or silicone sealant is suitable. Sometimes a transparent tool is used, but it is better to take white sealant.
  2. Alignment of the facade. Before gluing paper wallpapers, you need to leve the walls with a grinder. If thick canvases are used, then it is enough to wipe the base with sandpaper.
  3. The priming of the walls. It is better to choose acrylic mixtures with useful fillers. You need to primer at least twice. The second layer is applied when the first dries. If there was a dye in the acrylic primer, then after drying the layer you can proceed to the past. If soil without a coloring effect, the base must be painted in any light tone using the dye for the interior decoration. After painting, the slabs are again primed, then gluing begins.

Sticking wallpaper with putty

Although applying putty to attach wallpaper is a more time- and money-consuming process, the results will be superior and last longer. Prior to installing the wall, the pollution must be cleaned, the surfaces and seams of the plates must be strengthened, and the wall must be primed twice with acrylic or adhesive soil. A construction stapler is used to secure the grid. It is preferable to keep the spacing between the brackets to a maximum of 15 cm.

You can begin puttying once the soil has dried. In this instance, selecting the appropriate composition is crucial because plates cannot be processed using the mixture intended for brick and concrete. You must select unique varieties that are appropriate for the tree in order to prevent the wallpaper from pealing off with their putty. Three categories can comprise such putty:

  1. oil-glow;
  2. glue;
  3. Nitro-shpakleka.

It is permissible to use any of the compositions specified to arrange the plates. The manufacturer’s instructions are strictly followed when preparing the mixture for use.

The draft layer of lapwing covers the joints between panels and the plaster grid. Using a metal spatula, the plump are aligned once the soil has dried. They are executed at a sharp angle on the base. Once leveled, the wall is puttled once more. The dried surface is once more primed, sanded, and cleaned. Once this is done, you can glue any kind of finish.

Step Description
1 Prepare the surface by sanding the OSB plates to remove rough spots.
2 Clean the surface to remove dust and debris.
3 Apply a primer to seal the OSB and improve adhesion.
4 Let the primer dry completely before proceeding.
5 Cut the wallpaper to the required lengths, leaving extra for adjustments.
6 Apply wallpaper adhesive to the back of the wallpaper or directly on the wall, following the manufacturer"s instructions.
7 Start gluing the wallpaper from the top, aligning it carefully.
8 Smooth out air bubbles and wrinkles using a wallpaper brush or squeegee.
9 Trim excess wallpaper at the edges with a sharp knife.
10 Allow the wallpaper to dry as per the adhesive"s guidelines.

Careful planning and attention to detail are necessary for wallpaper application on OSB plates to be successful. In order to stop moisture absorption, which can cause the boards to swell and the wallpaper to peel, it’s critical to properly seal the OSB surface. Using a premium primer made especially for OSB is an essential first step.

After priming and prepping the surface, drywall compound is applied to help even out the OSB’s texture. This stage guarantees a seamless, uniform application of the wallpaper. For a professional look, sand the drywall compound to a smooth finish before applying wallpaper.

Making the correct adhesive choice is another crucial step. To ensure that the wallpaper adheres to the OSB properly, use a wallpaper paste that is strong and high-tack, specifically made for heavy materials. The best bond between the wallpaper and the substrate can be achieved by carefully adhering to the adhesive manufacturer’s instructions.

You can achieve a long-lasting and visually appealing wallpaper finish by taking the time to carefully prepare the OSB surface and using the appropriate materials. This technique improves the overall appearance of any room by turning the useful but rough OSB wall into a beautifully finished wall.

A smooth, long-lasting finish when gluing wallpaper onto OSB plates depends on careful preparation. In order to do this, the porous surface must first be sealed with an appropriate primer to stop moisture absorption, and then any rough spots or imperfections must be filled in with a layer of filler. Even application of wallpaper adhesive after the surface has been sealed and smoothed out guarantees a strong bond. With the correct techniques, OSB plates can be turned into a chic, long-lasting backdrop for any space.

Video on the topic

Glue wallpaper on the OSB is correct .

Wallpaper on the 2nd floor #1

How to paste wallpaper on OSB sheets

Liquid wallpaper on OSB

What color, in your opinion, is able to make a person happier?
Share to friends
Alice Chernyshev

Artist with 15 years of experience, color solutions specialist in interior design. I am in love with the world of colors from childhood, I am happy to share my knowledge and experience.

Rate author
Add a comment