How to glue meter wallpaper: nuances of high -quality gluing and a sequence of facing work

With fewer seams and a more seamless finish, meter wallpaper, also referred to as wide-width wallpaper, can completely change a space. However, there are unique difficulties when dealing with this larger-than-usual wallpaper. In order to attain a polished appearance, it’s critical to comprehend the subtleties of superior glue application and adhere to a well-defined process.

It’s important to prepare properly before starting. Make sure the walls are dry, smooth, and clean. Make sure to fill in any holes and smooth out any uneven areas on the wallpaper because any flaws will show through it. Accurate wall measurements will enable you to precisely cut the wallpaper, sparing you time and aggravation in the long run.

The kind of adhesive you use is very important when it comes to the actual gluing process. Select a premium wallpaper adhesive that is appropriate for the particular type of material used in your meter wallpaper. It is imperative to apply the adhesive uniformly to avoid wrinkles and bubbles. To ensure that the glue is completely covered on the wall and the back of the wallpaper, use a roller or brush.

Carefully align the first wallpaper strip, starting at a corner. Using a plastic smoother or wallpaper brush, smooth it down, making sure to push out any air bubbles by working from the center outward. Proceed to the following strip, taking care to match the pattern exactly. This step should be done slowly because even a slight misalignment can be seen.

Once all of the strips are positioned, trim any extra wallpaper from the edges and around any obstructions, such as outlets or light switches. To prevent stains, use a damp sponge to remove any extra adhesive. Before touching the wallpaper or adding any wall décor, let it dry completely.

These steps will help you achieve a professionally finished, elegantly wallpapered room by paying close attention to detail. When installed properly, meter wallpaper offers a stunning upgrade to any space because it has fewer seams and more design options.

Advantages and disadvantages of meter wallpaper

The term "meter wallpaper" is regarded as provisional since it covers a range of roll widths, including 1 meter, 90 cm, and much wider options. Wallcoverings from Belgian brands come in 1.4 m wide rolls.

Such a range originated overseas, and viewers were able to assess each of the paintings’ advantageous qualities there:

• Reducing the number of joints on the walls by two times or more, allows you to make a better -quality decoration.
• Saving time and effort to prepare for the pasting of the material. Cut it easier than 5 meter strips and stick them on the wall than 9-10 of the usual paintings.
• Lower cost compared to standard material. It is more profitable to buy 1 meter roll than two standard.

However, materials of this size have a number of drawbacks:

• The need to glue on a prepared and perfectly flat surface. Otherwise, the materials can not be perfectly engaged.
• Possible exceeding expenses, in comparison with the acquisition of materials from a traditional size. It is necessary to pre-calculate the dimensions of the room so that you do not have to buy a whole roll due to one missing strip.
• Since it is very difficult, and sometimes almost impossible to glue meter wallpaper, it is necessary to involve the assistant to the work.

Tools and materials for gluing

You must get the tools and supplies ready for work before adhering the meter wallpaper to the wall.

• Plumb.
• Roulette.
• Pencil.
• Putty knife.
• Roller.
• Maslar tape.
• A wide brush.
• Sponge.
• Knife.

Note: Walls need to be ready for meter wallpaper to be pasted. Consequently, it will use sandpaper to apply a layer of putty, primer, or grout correctly.

Depending on the type of wallpaper, you will either need to buy wallpaper glue ahead of time or select a universal composition.

Pre -preparation of walls

Knowing how to correctly apply meter wallpaper to the wall is insufficient. Even if you adhere to every guideline, poorly prepared walls will make this look utterly unappealing.

You must perform several common procedures to equalize the walls in order to precisely join the painting seams:

• Remove any extraneous objects from them, for example, nails, screws, screws, remove switches and sockets and for a while to seal holes with masking tape.
• Get rid of the remnants of the old coating: paints, plaster and wallpaper.
• Clean the surface of the base using sandpaper.
• If there are large defects on the wall, then the putty should be used to align them. Then you need to apply 2 layers of primer, since it will allow the glue not to absorb into the walls and increase the clutch.

Take note: They usually notice if non-woven wallpaper was selected for the job. Paint or white primer is therefore applied to the walls beneath them.

Typically, glue wallpaper cannot be started on a wall until the primer layer has dried completely.

Although adhering meter wallpaper might seem difficult, it can be done skillfully and efficiently with the appropriate method. This tutorial will take you through all of the necessary procedures and subtleties for applying beautiful wallpaper, from priming your walls to accurately cutting the wallpaper to applying adhesive and making sure everything lines up perfectly. These simple, easy-to-follow directions will help you achieve a flawless finish that elevates the beauty of any space.

Wall marking and cuts of canvases

You can begin working from any convenient location in the room because the material from the meter roll is glued to the joint.

1. To glue the first strip of wallpaper on the wall exactly, you will need both a plumb line and a pencil for a vertical line. Wallpaper from the drawn line are glued.

2. To calculate how many paintings will fit on a paper canvas, measure the walls’ height and length precisely before cutting any canvases.

3. Additionally, leave 10 cm on both the bottom and top of each wallpaper piece when cutting for a reserve. Recalling the pattern’s combination on the canvases is essential. The excess paint can be simply removed with a knife after the wallpaper has been glued to the walls and the glue has had time to dry.

4. With the front side down, begin rolling rolls on a dry, clean surface. The necessary length is marked using roulette, after which cuts are made, the roll is bent in half, and the fold is cut.

It’s crucial! The room where repairs are made must have a low relative humidity. In this room, you should also completely avoid drafts and extremely low temperatures. Ideal temperatures for this range are 15–25 °C.

Sticker process

The variety of wallpapers determines how they are applied:

• Paper. It is necessary to apply glue to the material. Playing are made on dry walls.
• Floselywain wallpaper. You need to work with them using the reverse technology, that is, the glue is applied to the wall and a dry strip of wallpaper is already attached to it.
• Meter vinyl wallpaper. It is necessary to smear with glue and canvas and wall. You should not attach baguettes to the glued wallpaper base. They must be recorded before the start of the past.

To hold a section of the canvas on two sides, you must use meter wallpaper in a team of at least two people.

The primary phases of the work:

1. A layer of glue is applied to the back of the finish. The wallpaper is applied to the dry wall or pre -lubricated with glue.

2. Apply glue to the wall, making sure to capture an extra 20 centimeters or so nearby. Using a brush, liberally apply a thick layer of glue to all corners and joints.

3. One person must hold the strip from above and precisely attach it to the wall-ceiling joint because the sheets must be glued from the ceiling vertically. In addition to holding the canvas’s lower edge, the second person should make sure the canvas and a vertical line coincide.

4. The strip is then made level. Using a plastic spatula or rubber roller, move the wallpaper from the center outward to remove any bubbles that may have formed beneath it.

5. You can start by adhering the first wallpaper sheet to the wall and then move on to the next. Additionally, 20 centimeters of space are left unglued on the wall. The process is crucial to preventing the adhesive composition from falling onto the wallpaper that has already been glued during the subsequent application.

6. A high-quality joint must be provided and the pattern on the canvases must be precisely combined.

Counseling! When the heating season has not yet started, you must schedule repairs for the warm season. Similar to drafts, hot air degrades the quality of glue. Wallpaper can wrinkle in the battery area.

Work in complex areas

People usually have trouble in places where it’s inconvenient to apply wallpaper, like corners, spaces close to batteries, above windows, and doorways.

It is advised to glue wallpaper that has been cut into small pieces in these areas. You must use slowly drying glue so that you can correct mistakes and make necessary adjustments.

Corners

The majority of the time, attempts to glue angles with wallpaper that is one meter wide or wider are unsuccessful and only result in distortions, fold formation, and other flaws.

Thus, in order to get a qualitative outcome, make use of the following advice:

• In the corner zone, glue the sheet so that most of the canvas is on one wall and for 5 cm goes to the adjacent.
• On the allowance you need to find the narrowest place, retreat 1 cm from the edge of the wallpaper, apply marking for a vertical line.
• The next canvas is glued over this marking.
• The seams can be cut using a spatula, ruler, stationery knife.

Batteries

Wallpapering the area close to the battery needs to be done as last-minute as possible, with the utmost precision, creativity, and resourcefulness:

• It is necessary to cut off a sheet of wallpaper by the size of the niche for radiators.
• In the place where the battery mount will be located, you need to make a vertical incision.
• The sheet is covered with glue and starts behind the pipes. It is necessary to carefully straighten the folds that appeared on the sheet and press it tightly against the wall.
• It will be inconvenient to use a roller in such a place, so a rag will come in handy.
• The excess part is overlapped on the edge of the wallpaper, tightly pressed by a spatula. Excesses are cut.

If applying wallpaper close to the battery is not feasible in this manner, you can fill in the difficult-to-reach areas by cutting the canvas into smaller pieces.

Sockets and switches

It’s necessary to paste entire sheets of wallpaper on the wall because all switches and sockets were taken out before the wallpaper was applied. Through them, the shapes of previous holes will be visible.

Make a cross-shaped cut inside the paper with a stationery knife, and then season the remaining portion.

Counseling! An incision in the shape of a star must be made if the socket holes are round.

Openings

Paperwork needs to be cut when working around window and door openings. They must first be cut to fit the size of the opening, and the pattern must be combined.

Step	Details
1. Surface Preparation	Clean the wall, remove old wallpaper, and fill any holes or cracks.
2. Cutting Wallpaper	Measure and cut wallpaper strips to the height of the wall, leaving a few extra centimeters.
3. Applying Glue	Spread the glue evenly on the back of the wallpaper using a brush or roller.
4. Positioning Wallpaper	Carefully position the wallpaper strip on the wall, starting from the top and smoothing it downwards.
5. Smoothing	Use a smoothing tool to remove air bubbles and ensure the wallpaper is flat.
6. Trimming Edges	Trim excess wallpaper along the edges and corners with a sharp knife.
7. Repeat	Repeat the process for each strip, ensuring the patterns match up.
8. Finishing Touches	Check for any bubbles or loose edges and smooth them out.

Any room can be transformed with meter wallpaper, adding a modern and fashionable look. You can achieve a long-lasting professional finish by paying attention to important details and following the correct procedures. The basis for your wallpapering project is a clean, smooth surface, so don’t forget to start there. Make sure the walls are dry and dust-free, fill in any holes, and smooth down any uneven areas.

The longevity of your wallpaper depends on the adhesive you choose. Use a paste that is high-quality and appropriate for the kind of wallpaper you are using. Follow the manufacturer’s instructions for applying the adhesive, making sure to leave enough time for drying. This facilitates the creation of a solid bond between the wall and the wallpaper.

It’s important to hang the wallpaper precisely. To ensure a perfect fit, allow a small amount of extra wallpaper at the top and bottom to be trimmed off after you measure and cut your strips. To prevent misalignment, begin in the center of the wall and work your way outward. Using a wallpaper brush or smoother, work from the center outward to remove any wrinkles or air bubbles.

Lastly, give the final details some extra time. Using a sharp utility knife, carefully trim any excess wallpaper around any fixtures, baseboards, and the ceiling. Any extra adhesive should be wiped off right away to avoid it drying up and leaving marks. Your wallpapering project will provide exquisitely decorated walls that improve your living area if you are patient and pay close attention to detail.

Video on the topic

How to stick murals with one canvas? The advice of the master!!! how to glue non -woven wallpaper, wrapping wallpaper

How to glue non -woven wallpaper properly?

How to glue monophonic non -woven wallpaper. Useful tips

Picking of wallpaper in overlap! Instructions from Astana!

How to stick wallpaper in the corners correctly

How to glue wallpaper so that the seams do not disperse?